Lincoln Lubrication

246002  |  Hose End for 1/8" ID Hose

Pump discharges lubricant on air-powered forward stroke and vents on springpowered return stroke through built-in check/vent valve. Reservoir is translucent with spring-loaded follower. Includes filler fitting for refilling reservoir with Model 81834 or other manual pump equipped with Model 645006 coupler.

Lubricant / Air Ratio: 20:1
Max. Output: 0.45 cu. in.
Reservoir Capacity: 4 lb. / 120 cu. in.
Reservoir Temp Range: 0 F to 150 F
Air Inlet: 1/4" NPTF (F)
Lube Outlet: 1/4" NPTF (F)
Lubricant Oper. Pressure (Min. / Max.): 1200 psig / 3500 psig
Dimensions (HxWxL): 18 1/2" x 5 1/4" x 6"
Air Valve Required: 3-way

Note:  Air consumption @ 100 psi is 0.15 CFM per stroke.

 

Timer Specifications

Cycle Time (Min./Max.): 20 sec. / 24 hr.
On Time (Min./Max.): 10 sec. / 1 min.
Power Requirements: 120 VAC, 60 hz
Ambient Oper. Temp. Range: 10 F to +150 F

 

 

Product image is for representation only.

  • For single-line central lubrication system.
  • For dispensing fluid or semi-fluid lubricants.
  • Output is externally adjustable.
  • Indicator stem permits visual check of injector operation.
  • May be combined in a circuit of injectors SL-43, SL-41 and/or SL-44.
  • Individual injectors can be easily removed for inspection or replacement.
  • Carbon steel injectors with Nitrile or flouroelastomer packings.
  • Injectors with flouroelastomer packings are used for heat resistant applications or when lubricant to be dispensed requires flouroelastomer packings for compatibility (indicated by black adjustment caps).
Output Min./Max. 0.001 cu. in. / 0.016 cu. in.
Operating Pressure Min./Max. 750 psig / 1000 psig
Operating Pressure - Typical 850 psig
Operating Pressure - Vent 150 psig
Manifold Inlet Connection 1/8" NPTF (F)
Injector Outlet Connection 1/8"O.D. tube connection

 

 Model Number of Outlets A Dimension B Dimension
Heat Resistant 1 1 1/8" 1 5/8"

 

Notes:

  1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing – 1/8" O.D. as standard. Other outlet connectors for feed line optional.
  2. Injectors with manifolds include two mounting clips and screws.
  3. Standard injectors have Nitrile packings (200°F/93°C max.); Heat Resistant injectors have flouroelastomer packings (350°F/176°C max., depending on lubricant used) and black adjusting cap. Check packing compatibility with synthetic lubricants.Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./turn.

 

 

Note:  Product images are for representation only.

  • For single-line central lubrication system.
  • For dispensing fluid or semi-fluid lubricants.
  • Output is externally adjustable.
  • Indicator stem permits visual check of injector operation.
  • May be combined in a circuit of injectors SL-43, SL-41 and/or SL-44.
  • Individual injectors can be easily removed for inspection or replacement.
  • Carbon steel injectors with Nitrile or flouroelastomer packings.
  • Injectors with flouroelastomer packings are used for heat resistant applications or when lubricant to be dispensed requires flouroelastomer packings for compatibility (indicated by black adjustment caps).
Output Min./Max. 0.001 cu. in. / 0.016 cu. in.
Operating Pressure Min./Max. 750 psig / 1000 psig
Operating Pressure - Typical 850 psig
Operating Pressure - Vent 150 psig
Manifold Inlet Connection 1/8" NPTF (F)
Injector Outlet Connection 1/8"O.D. tube connection

 

 Model Number of Outlets A Dimension B Dimension
Standard 10 7 7/8" 8 3/8"

 

Notes:

  1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing – 1/8" O.D. as standard. Other outlet connectors for feed line optional.
  2. Injectors with manifolds include two mounting clips and screws.
  3. Standard injectors have Nitrile packings (200°F/93°C max.); Heat Resistant injectors have flouroelastomer packings (350°F/176°C max., depending on lubricant used) and black adjusting cap. Check packing compatibility with synthetic lubricants.Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./turn.

 

 

Note:  Product images are for representation only.

  • For single-line central lubrication system.
  • For dispensing fluid or semi-fluid lubricants.
  • Output is externally adjustable.
  • Indicator stem permits visual check of injector operation.
  • May be combined in a circuit of injectors SL-43, SL-41 and/or SL-44.
  • Individual injectors can be easily removed for inspection or replacement.
  • Carbon steel injectors with Nitrile or flouroelastomer packings.
  • Injectors with flouroelastomer packings are used for heat resistant applications or when lubricant to be dispensed requires flouroelastomer packings for compatibility (indicated by black adjustment caps).
Output Min./Max. 0.001 cu. in. / 0.016 cu. in.
Operating Pressure Min./Max. 750 psig / 1000 psig
Operating Pressure - Typical 850 psig
Operating Pressure - Vent 150 psig
Manifold Inlet Connection 1/8" NPTF (F)
Injector Outlet Connection 1/8"O.D. tube connection

 

 Model Number of Outlets A Dimension B Dimension
Standard 4 3 3/8" 3 7/8"

 

Notes:

  1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing – 1/8" O.D. as standard. Other outlet connectors for feed line optional.
  2. Injectors with manifolds include two mounting clips and screws.
  3. Standard injectors have Nitrile packings (200°F/93°C max.); Heat Resistant injectors have flouroelastomer packings (350°F/176°C max., depending on lubricant used) and black adjusting cap. Check packing compatibility with synthetic lubricants.Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./turn.

 

 

Note:  Product images are for representation only.

  • For single-line central lubrication system.
  • For dispensing fluid or semi-fluid lubricants.
  • Output is externally adjustable.
  • Indicator stem permits visual check of injector operation.
  • May be combined in a circuit of injectors SL-43, SL-41 and/or SL-44.
  • Individual injectors can be easily removed for inspection or replacement.
  • Carbon steel injectors with Nitrile or flouroelastomer packings.
  • Injectors with flouroelastomer packings are used for heat resistant applications or when lubricant to be dispensed requires flouroelastomer packings for compatibility (indicated by black adjustment caps).
Output Min./Max. 0.001 cu. in. / 0.016 cu. in.
Operating Pressure Min./Max. 750 psig / 1000 psig
Operating Pressure - Typical 850 psig
Operating Pressure - Vent 150 psig
Manifold Inlet Connection 1/8" NPTF (F)
Injector Outlet Connection 1/8"O.D. tube connection

 

 Model Number of Outlets A Dimension B Dimension
Standard 2 1 7/8" 2 3/8"

 

Notes:

  1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing – 1/8" O.D. as standard. Other outlet connectors for feed line optional.
  2. Injectors with manifolds include two mounting clips and screws.
  3. Standard injectors have Nitrile packings (200°F/93°C max.); Heat Resistant injectors have flouroelastomer packings (350°F/176°C max., depending on lubricant used) and black adjusting cap. Check packing compatibility with synthetic lubricants.Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./turn.

 

 

Note:  Product images are for representation only.

  • For single-line, high-pressure central lubrication system.
  • For dispensing lubricants compatible with polyurethane seals up to NLGI No. 2 (refer to Design Guide).
  • Output is externally adjustable.
  • Indicator stem permits visual check of injector operation.
  • May be combined in a circuit of injectors SL-32, SL-33, SL-1, SL-V and/or SL-11.
  • Individual injectors can be easily removed for inspection or replacement.
  • Two SL-V XL injectors are required to replace one SL-11 injector.
  • Each SL-V XL injector includes a clear polycarbonate protective cap
Material Carbon Steel
Output Min. / Max. 0.015 cu. in. / 0.305 cu. in.
Operating Pressure Min. / Max. 1850 psig / 6000 psig
Operating Pressure - Typical 2500 psig
Operating Pressure - Vent 1000 psig
Manifold Inlet 3/8" NPTF
Injectout Outlet 1/8" NPTF

 

Model Specifications

Type Three Injector Manifold
Number of Outlets 3
A Dimension 1 1/4"
B Dimension 4 1/4"

 

Notes:

  1. Injector manifolds have 13⁄32" (10.3 mm) dia. mounting holes for 3⁄8" bolt.
  2. Injectors have polyurethane seals. Check compatibility with synthetic lubricants.
  3. Injector rated for 180°F (80°C) max. ambient temperature, depending on lubricant used.
  4. Injectors include fitting for filling feedlines via alternate outlet port.
  5. Output with adjustment screw hand-tightened is .015 cu. in. Maximum output is achieved with 20 1/2 turns at .014 cu. in./turn.

 

Product images are for representation only.

  • For single-line, high-pressure central lubrication system
  • For dispensing petroleum-based lubricants with a viscosity up to NLGI No. 2
  • Output is externally adjustable
  • Indicator stem permits visual check of injector operation
  • May be combined in a circuit of Injectors SL-32, SL-V, SL-V XL, SL-1 and/or SL-11
  • Individual injectors can be easily removed for inspection or replacement
  • Available in stainless steel SAE 304, for application where environmental conditions are hazardous to carbon steel or in industries preferring stainless steel

Specifications:

  • Output:
    • Minimum: .001 cu. in. (.016 cc)
    • Maximum: .003 cu. in. (.049 cc)
  • Operating pressure:
    • Minimum: 1200 psig (83 bar)
    • Maximum: 3500 psig (241 bar)
    • Typical: 1500 psig (103 bar)
    • Vent: 200 psig (14 bar)

 

Material 304 Stainless Steel
Number of Outlets -
Manifold Inlet Connection NPTF -
Injector Outlet Connection O.D. Tube 1/8"
A Dimension Single Replacement Injector
B Dimension Single Replacement Injector

 

Note:

  1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing. - 1/8" O.D. as standard. Other outlet connectors for feed line optional.
  2. Injectors with manifolds include two mounting clips and screws.
  3. Injectors have nitrile packings (200°F max. (93°C)). Checking packing compatibility with synthetic lubricants.
  4. Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with two turns at .001 cu. in./ turn.

 

Note:  Product images are for representation only.

62256  |  Quicklub Nylon Tubing
404-22581-2  |  Ferrule

Automatically adjusts to handle a variety of electrical supply voltages (between 94- and 265-volt, 50 to 60 Hz).

Input Voltage: 94 0 265 VAC, 3 Amps
Operating Temperature: -13 F to 158 F / -25 C to 70 C
Number & Element Size: 1 - 6 mm
Reservoir Capacity: 2-, 4-, 8- or 15- liter*
Output per Minute: Approx. 2.8 cc
Lubricant: Greases up to NGLI #2 / Oil with at least 40 cSt
Max. Operating Pressure: 5076 psi

* Contact us for 15-liter reservoir models

Model Specifications

Description: P203-4XNBO-1K6-AC-1A1.01-V10 (UL)-A+SV
Res. Cap.: 4 liter
Grease or Oil: Grease
Low Level Control: No
Printed Circuit Board: Yes

"(UL)" in the description refers to UL-approved, CSA-certified pumps.
Pumps with "-A+SV" come complete with the 1/8" NPT adapter and pressure relief valve.

 

 

Product image is for representation only.

Electric grease pump with integrated on/off controller.

Output/Min Per Element** 0.171 cu. in.
Lubricant Outlet 1/8" NPT (F)
Max. System Operating Pressure 5000 psig
Enclosure Rating IP6K9K*
Operating Temp. Range Min. -13 F / -25 C to Max. 158 F / 70 C
Reservoir Capacity 2-, 4-, 8- or 15-liter ***
Reservoir Fill Method By grease fitting
Pressure Relief Valve 4000 psi +/- 250 psi

*    Protected from water sprayed in all directions.
**  Single 6 mm element standard; to increase pump output, add one or two additional element(s) #600-26876-2 and relief valve #270864
*** Pressure relief Valve included with these models.

Model Specifications

Electrical Requirements 24 VDC / 2 Amp
Interval Timer Setting - On Time* (2 min. increments) Minimum 2 minutes
Interval Timer Setting - On Time* (2 min. increments) Maximum 30 minutes
Interval Timer Setting - Off Time (1 hr. increment) Minimum 1 hour
Interval Timer Setting - Off Time (1 hr. increment) Maximum 15 hours
Reservoir Capacity 4 lbs / 1.8 kg / 2 liter

 

 

NOTE:  Product images are for representation only.

Type 3-Way
Power Requirements 110 VAC, 50 Hz
120 VAC, 60 Hz
11 VA
Inrush Current Amps 0.12
Holding Current Amps 0.09
Air Inlet / Outlet 3/8" NPT(F)
Ambient Temp. Range 0 F to 120 F
Cv Factor 4.4
Max Pressure 150 psi
Conduit Connection 1/2" NPT(F)

 

 

Product image is for representation only.

  • For single-line, high-pressure central lubrication system.
  • For dispensing lubricants compatible with flouroelastomer packings and viscosity up to NLGI No. 2 (refer to Design Guide).
  • Output is externally adjustable.
  • Indicator stem permits visual check of injector operation.
  • May be combined in a circuit of injectors SL-33, SL-V, SL-V XL and/or SL-11.
  • Individual injectors can be easily removed for inspection or replacement.
  • Available in stainless steel SAE 304, for application where environmental conditions are hazardous to carbon steel or in industries preferring stainless steel.
Output Min./Max. 0.001 cu. in. / 0.008 cu. in.
Operating Pressure Min./Max. 1200 psig / 3500 psig
Operating Pressure - Typical 1500 psig
Operating Pressure - Vent 200 psig
Manifold Inlet Connection 1/4" NPTF (F)
Injector Outlet Connection 1/8" O.D. Tube

 

Material Number of Outlets A Dimension B Dimension
Carbon Steel 3 2 3/4" 3 1/4"

 

 

Notes:

1. Injectors, except replacement injectors for manifold, include compression nut and ferrule for tubing — 1/8" O.D. as standard. Other outlet connectors for feed line optional.

2. Injectors with manifolds include two mounting clips and screws.

3. Injectors have Nitrile packings (200°F max. / 93°C). Check packing compatibility with synthetic lubricants.

4. Output with indicator cap hand-tightened is .001 cu. in. Maximum output is achieved with five turns at .0014 cu. in./turn.

 

Note:  Product images are for representation only.

619-27122-1  |  SSV Divider Valve

Construction Material Carbon Steel
Max. Operating Pressure / Min. Operating Pressure 5076 psig / 290 psig
Output/Cycle per Outlet 0.012 cu. in.
Lubricant Inlet 1/8" NPTF (F)
Lubricant Outlet M10x1
Operating Temperature Min. / Max. -22F / 212F
Dimension A 2.36"
Max. Number of Outlets 6
Cycle Indicator Pin Yes

 

Notes:  

  1. Lubricant outlet must use Lincoln Quicklub fittings.  
  2. * 241650 stainless steel adapter available to convert inlet to 1/8" NPTF.
  3. You must use outlets 1 and 2 to allow the system to operate properly.

 

Product images are for representation only.

619-26646-2  |  SSV Divider Valve

Construction Material Carbon Steel
Max. Operating Pressure / Min. Operating Pressure 5076 psig / 290 psig
Output/Cycle per Outlet 0.012 cu. in.
Lubricant Inlet 1/8" NPTF (F)
Lubricant Outlet M10x1
Operating Temperature Min. / Max. -22F / 212F
Dimension A 2.95"
Max. Number of Outlets 8
Cycle Indicator Pin Yes

 

Notes:  

  1. Lubricant outlet must use Lincoln Quicklub fittings.  
  2. * 241650 stainless steel adapter available to convert inlet to 1/8" NPTF.
  3. You must use outlets 1 and 2 to allow the system to operate properly.

 

 

Note:  Product images are for respresentation only.